English and Chinese Version

English   Chinese

You are here:Home»Battery Powered Tools »EZ-60UNV Multi-Function Battery Hydraulic Tools for cutting, crimping,and punching

EZ-60UNV Multi-Function Battery Hydraulic Tools for cutting, crimping,and punching

Rate this item
(3 votes)

EZ series Battery-Powered Hydraulic Tools powered by 18V Lithium-Ion Batteries offering 50% higher capacity, with Crimping,Cutting and Punching multi-function.  

  • The tool incorporates an automatic retraction function which returns the piston to its starting position when the work is complete.

  • A manual retraction button allows the user to return the piston to the starting position in case of an jam. The tool is equipped with a special brake that stops the forward motion of the piston when the trigger is released.

  • The tool is equipped with a double piston pump to ensure precise and accurate cutting, crimping or punching motion.

  • The head can be turned 360o in order to gain better access to the work.

  • Li-ion batteries do not have a memory and do not self discharge. Even after long periods of being idle the tool is always ready to operate. Another feature is the low-power -to-weight ratio providing 50% more capacity and shorter charging cycles when compared to NiMH batteries.

  • An in-built safety temperature sensor stops the tool automatically if the battery temperature exceeds 60oC. A fault signal sounds rendering the tool inoperative until the normal operating temperature is restored.

Specification for EZ-60UNV Multi-Function Battery Hydraulic Tools for cutting, crimping,and punching

Crimping force:

60KN

Stroke:

42mm

Cutting cycle:

70times

Cutting range:

Dia. 40mm(Cu/Al and armored cable)

Crimping cycle:

320times

Crimping range:

16-300mm2

Punching cycle:

100times

Punching range:

Dia.22.5- Dia.61.5mm

Round punch Max.:

61.5mm

Voltage:

18V

Capacity:

3.0Ah

Charging time:

2hours

Package:

Steel case

ACCESSORIES:

Crimping dies: 16, 25, 35, 50, 70, 95, 120, 150, 185, 240, 300mm2

Punches dies(Type C): 22.5, 28.3, 34.6, 43.2, 49.6, 61.5mm

Blade:

1set

Adapter for crimping:

1pc

Adapter for punching:

1pc

3/4”, 16UN Draw stud:

1pc

7/16”, 20UN Draw stud:

1pc

Spacer

1pc

Battery:

1pc

Charger:

1pc

Sealing ring of cylinder:

1set

Sealing ring of safety valve:

1set

Description of components of 6 Tonne, Flip-Top Head, Crimp, Cut, Hole Punch Tool

 ez-60unv battery hydraulic cutter puncher crimper

Code

Description

Function

1

latch

For locking the head

2

Retaining clips

For locking/unlocking the dies/blade holder

3

LED indicator

For indicating the operating condition and battery discharging situation.

4

Retract button

For manual retracting the piston in case of an incorrect operation.

5

Trigger

For starting operation

6

Battery lock

For locking/unlocking the battery.

7

Battery

For supplying power, rechargeable Li-ion(18V).

8

Stud

For connecting die during operation

9

Punch&Die

For punching

10

Adaptor

For assisting punching operation

11

Die holder

For fixing crimping die

12

Retaining clips

For locking/ unlocking the crimping die

13

Die

For crimping, interchangeable crimping die

14

Blade

For cable cutting.

 

Usage of the tool for 

6 Tonne, Flip-Top Head, Crimp, Cut, Hole Punch Tool

 1) Cutting Version

Press the battery lock and take out the battery if it is lacking power put it back after charging. Pull out the lock and open the head, insert the two blades, put cable between two blades and fully close the head, press the trigger and begin to cut. The tool will retract automatically after cutting, switch the button in case of an incorrect operation, please see the illustration below.

 2) Crimping Version

Select the right dies for the intended application, 

Don’t operate the tool without dies. Please select the correct die according to the AL/Cu terminal for intended, to choose the wrong die may cause loose crimping result or generate a lot of burs.

 Pull out the latch and open the lock-hook, insert two dies, put cable and lugs between two dies and fully close the head, press the trigger and begin to crimp. The tool will retract automatically after crimping, press the button in case of an incorrect operation, please see the illustration below.

 3) Punching Version

 a)Pull out the latch and open the lock-hook, settle the adaptor. (as the illustrationto preparing working)

  1. b)Close the lock-hook, and press the button to return the piston.
  2. c)Select the suitable punch die with stud and settle onto the head for punching
  3. d)Dill a lead hole at the center point of the hole marked and measured
  4. e)Thread the Threaded Stud into the punch head
  5. f)The spacer is to be used with all punch and dies that are used to protect the head. Slide the spacer down onto the threaded stud, then slide the die onto the Threaded Stud so that it sits flat on the spacer. After that slide the work piece with the drilled hole down onto the die Thread the punch onto the work piece as tightly as possible
  6. g)Switch the trigger to start punching, keep pressing until the punch has punched through the work piece. The tool will retract automatically after punching
  7. h)Press the retract button in case of an incorrect operation

Capacity and Draw Stud Selection Guide

 

Draw Studs and Accessories

Standard Round Knockout Punches (Type D)

22.5mm

28.3mm

34.6mm

43.2mm

49.6mm

61.5mm

7/16”Draw Stud

+Spacer

 

 

 

 

 

3/4”Draw Stud

+Spacer

 

 

 

3/4”Draw Stud

 

 

 

 

 

6 Tonne Flip-Top Head Crimp Cut Hole Punch Tool 

 

The package for  EZ-60UNV Multi-Function Battery Hydraulic Tools for cutting, crimping,and punching 

EZ-60UNV Multi-Function Battery Hydraulic Tools for cut punch crimp package

Read 152 times Last modified on Wednesday, 18 June 2014 21:30

Service

About Us

Relationship

Follow Us On

facebookFacebook

 twitterTwitter

 linkedinLinkedin

youtubeYoutube